forked from forks/qmk_firmware
361 lines
15 KiB
PHP
361 lines
15 KiB
PHP
|
/* Name: usbdrvasm20.inc
|
||
|
|
* Project: V-USB, virtual USB port for Atmel's(r) AVR(r) microcontrollers
|
||
|
|
* Author: Jeroen Benschop
|
||
|
|
* Based on usbdrvasm16.inc from Christian Starkjohann
|
||
|
|
* Creation Date: 2008-03-05
|
||
|
|
* Tabsize: 4
|
||
|
|
* Copyright: (c) 2008 by Jeroen Benschop and OBJECTIVE DEVELOPMENT Software GmbH
|
||
|
|
* License: GNU GPL v2 (see License.txt), GNU GPL v3 or proprietary (CommercialLicense.txt)
|
||
|
|
* Revision: $Id: usbdrvasm20.inc 740 2009-04-13 18:23:31Z cs $
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Do not link this file! Link usbdrvasm.S instead, which includes the
|
||
|
|
* appropriate implementation!
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
General Description:
|
||
|
|
This file is the 20 MHz version of the asssembler part of the USB driver. It
|
||
|
|
requires a 20 MHz crystal (not a ceramic resonator and not a calibrated RC
|
||
|
|
oscillator).
|
||
|
|
|
||
|
|
See usbdrv.h for a description of the entire driver.
|
||
|
|
|
||
|
|
Since almost all of this code is timing critical, don't change unless you
|
||
|
|
really know what you are doing! Many parts require not only a maximum number
|
||
|
|
of CPU cycles, but even an exact number of cycles!
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define leap2 x3
|
||
|
|
#ifdef __IAR_SYSTEMS_ASM__
|
||
|
|
#define nextInst $+2
|
||
|
|
#else
|
||
|
|
#define nextInst .+0
|
||
|
|
#endif
|
||
|
|
|
||
|
|
;max stack usage: [ret(2), YL, SREG, YH, bitcnt, shift, x1, x2, x3, x4, cnt] = 12 bytes
|
||
|
|
;nominal frequency: 20 MHz -> 13.333333 cycles per bit, 106.666667 cycles per byte
|
||
|
|
; Numbers in brackets are clocks counted from center of last sync bit
|
||
|
|
; when instruction starts
|
||
|
|
;register use in receive loop:
|
||
|
|
; shift assembles the byte currently being received
|
||
|
|
; x1 holds the D+ and D- line state
|
||
|
|
; x2 holds the previous line state
|
||
|
|
; x4 (leap) is used to add a leap cycle once every three bytes received
|
||
|
|
; X3 (leap2) is used to add a leap cycle once every three stuff bits received
|
||
|
|
; bitcnt is used to determine when a stuff bit is due
|
||
|
|
; cnt holds the number of bytes left in the receive buffer
|
||
|
|
|
||
|
|
USB_INTR_VECTOR:
|
||
|
|
;order of registers pushed: YL, SREG YH, [sofError], bitcnt, shift, x1, x2, x3, x4, cnt
|
||
|
|
push YL ;[-28] push only what is necessary to sync with edge ASAP
|
||
|
|
in YL, SREG ;[-26]
|
||
|
|
push YL ;[-25]
|
||
|
|
push YH ;[-23]
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
; Synchronize with sync pattern:
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
;sync byte (D-) pattern LSb to MSb: 01010100 [1 = idle = J, 0 = K]
|
||
|
|
;sync up with J to K edge during sync pattern -- use fastest possible loops
|
||
|
|
;The first part waits at most 1 bit long since we must be in sync pattern.
|
||
|
|
;YL is guarenteed to be < 0x80 because I flag is clear. When we jump to
|
||
|
|
;waitForJ, ensure that this prerequisite is met.
|
||
|
|
waitForJ:
|
||
|
|
inc YL
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
brne waitForJ ; just make sure we have ANY timeout
|
||
|
|
waitForK:
|
||
|
|
;The following code results in a sampling window of < 1/4 bit which meets the spec.
|
||
|
|
sbis USBIN, USBMINUS ;[-19]
|
||
|
|
rjmp foundK ;[-18]
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
sbis USBIN, USBMINUS
|
||
|
|
rjmp foundK
|
||
|
|
#if USB_COUNT_SOF
|
||
|
|
lds YL, usbSofCount
|
||
|
|
inc YL
|
||
|
|
sts usbSofCount, YL
|
||
|
|
#endif /* USB_COUNT_SOF */
|
||
|
|
#ifdef USB_SOF_HOOK
|
||
|
|
USB_SOF_HOOK
|
||
|
|
#endif
|
||
|
|
rjmp sofError
|
||
|
|
foundK: ;[-16]
|
||
|
|
;{3, 5} after falling D- edge, average delay: 4 cycles
|
||
|
|
;bit0 should be at 34 for center sampling. Currently at 4 so 30 cylces till bit 0 sample
|
||
|
|
;use 1 bit time for setup purposes, then sample again. Numbers in brackets
|
||
|
|
;are cycles from center of first sync (double K) bit after the instruction
|
||
|
|
push bitcnt ;[-16]
|
||
|
|
; [---] ;[-15]
|
||
|
|
lds YL, usbInputBufOffset;[-14]
|
||
|
|
; [---] ;[-13]
|
||
|
|
clr YH ;[-12]
|
||
|
|
subi YL, lo8(-(usbRxBuf));[-11] [rx loop init]
|
||
|
|
sbci YH, hi8(-(usbRxBuf));[-10] [rx loop init]
|
||
|
|
push shift ;[-9]
|
||
|
|
; [---] ;[-8]
|
||
|
|
ldi shift,0x40 ;[-7] set msb to "1" so processing bit7 can be detected
|
||
|
|
nop2 ;[-6]
|
||
|
|
; [---] ;[-5]
|
||
|
|
ldi bitcnt, 5 ;[-4] [rx loop init]
|
||
|
|
sbis USBIN, USBMINUS ;[-3] we want two bits K (sample 3 cycles too early)
|
||
|
|
rjmp haveTwoBitsK ;[-2]
|
||
|
|
pop shift ;[-1] undo the push from before
|
||
|
|
pop bitcnt ;[1]
|
||
|
|
rjmp waitForK ;[3] this was not the end of sync, retry
|
||
|
|
; The entire loop from waitForK until rjmp waitForK above must not exceed two
|
||
|
|
; bit times (= 27 cycles).
|
||
|
|
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
; push more registers and initialize values while we sample the first bits:
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
haveTwoBitsK:
|
||
|
|
push x1 ;[0]
|
||
|
|
push x2 ;[2]
|
||
|
|
push x3 ;[4] (leap2)
|
||
|
|
ldi leap2, 0x55 ;[6] add leap cycle on 2nd,5th,8th,... stuff bit
|
||
|
|
push x4 ;[7] == leap
|
||
|
|
ldi leap, 0x55 ;[9] skip leap cycle on 2nd,5th,8th,... byte received
|
||
|
|
push cnt ;[10]
|
||
|
|
ldi cnt, USB_BUFSIZE ;[12] [rx loop init]
|
||
|
|
ldi x2, 1<<USBPLUS ;[13] current line state is K state. D+=="1", D-=="0"
|
||
|
|
bit0:
|
||
|
|
in x1, USBIN ;[0] sample line state
|
||
|
|
andi x1, USBMASK ;[1] filter only D+ and D- bits
|
||
|
|
rjmp handleBit ;[2] make bit0 14 cycles long
|
||
|
|
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
; Process bit7. However, bit 6 still may need unstuffing.
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
|
||
|
|
b6checkUnstuff:
|
||
|
|
dec bitcnt ;[9]
|
||
|
|
breq unstuff6 ;[10]
|
||
|
|
bit7:
|
||
|
|
subi cnt, 1 ;[11] cannot use dec becaus it does not affect the carry flag
|
||
|
|
brcs overflow ;[12] Too many bytes received. Ignore packet
|
||
|
|
in x1, USBIN ;[0] sample line state
|
||
|
|
andi x1, USBMASK ;[1] filter only D+ and D- bits
|
||
|
|
cpse x1, x2 ;[2] when previous line state equals current line state, handle "1"
|
||
|
|
rjmp b7handle0 ;[3] when line state differs, handle "0"
|
||
|
|
sec ;[4]
|
||
|
|
ror shift ;[5] shift "1" into the data
|
||
|
|
st y+, shift ;[6] store the data into the buffer
|
||
|
|
ldi shift, 0x40 ;[7] reset data for receiving the next byte
|
||
|
|
subi leap, 0x55 ;[9] trick to introduce a leap cycle every 3 bytes
|
||
|
|
brcc nextInst ;[10 or 11] it will fail after 85 bytes. However low speed can only receive 11
|
||
|
|
dec bitcnt ;[11 or 12]
|
||
|
|
brne bit0 ;[12 or 13]
|
||
|
|
ldi x1, 1 ;[13 or 14] unstuffing bit 7
|
||
|
|
in bitcnt, USBIN ;[0] sample stuff bit
|
||
|
|
rjmp unstuff ;[1]
|
||
|
|
|
||
|
|
b7handle0:
|
||
|
|
mov x2,x1 ;[5] Set x2 to current line state
|
||
|
|
ldi bitcnt, 6 ;[6]
|
||
|
|
lsr shift ;[7] shift "0" into the data
|
||
|
|
st y+, shift ;[8] store data into the buffer
|
||
|
|
ldi shift, 0x40 ;[10] reset data for receiving the next byte
|
||
|
|
subi leap, 0x55 ;[11] trick to introduce a leap cycle every 3 bytes
|
||
|
|
brcs bit0 ;[12] it will fail after 85 bytes. However low speed can only receive 11
|
||
|
|
rjmp bit0 ;[13]
|
||
|
|
|
||
|
|
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
; Handle unstuff
|
||
|
|
; x1==0xFF indicate unstuffing bit6
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
|
||
|
|
unstuff6:
|
||
|
|
ldi x1,0xFF ;[12] indicate unstuffing bit 6
|
||
|
|
in bitcnt, USBIN ;[0] sample stuff bit
|
||
|
|
nop ;[1] fix timing
|
||
|
|
unstuff: ;b0-5 b6 b7
|
||
|
|
mov x2,bitcnt ;[3] [2] [3] Set x2 to match line state
|
||
|
|
subi leap2, 0x55 ;[4] [3] [4] delay loop
|
||
|
|
brcs nextInst ;[5] [4] [5] add one cycle every three stuff bits
|
||
|
|
sbci leap2,0 ;[6] [5] [6]
|
||
|
|
ldi bitcnt,6 ;[7] [6] [7] reset bit stuff counter
|
||
|
|
andi x2, USBMASK ;[8] [7] [8] only keep D+ and D-
|
||
|
|
cpi x1,0 ;[9] [8] [9]
|
||
|
|
brmi bit7 ;[10] [9] [10] finished unstuffing bit6 When x1<0
|
||
|
|
breq bitloop ;[11] --- [11] finished unstuffing bit0-5 when x1=0
|
||
|
|
nop ;--- --- [12]
|
||
|
|
in x1, USBIN ;--- --- [0] sample line state for bit0
|
||
|
|
andi x1, USBMASK ;--- --- [1] filter only D+ and D- bits
|
||
|
|
rjmp handleBit ;--- --- [2] make bit0 14 cycles long
|
||
|
|
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
; Receiver loop (numbers in brackets are cycles within byte after instr)
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
bitloop:
|
||
|
|
in x1, USBIN ;[0] sample line state
|
||
|
|
andi x1, USBMASK ;[1] filter only D+ and D- bits
|
||
|
|
breq se0 ;[2] both lines are low so handle se0
|
||
|
|
handleBit:
|
||
|
|
cpse x1, x2 ;[3] when previous line state equals current line state, handle "1"
|
||
|
|
rjmp handle0 ;[4] when line state differs, handle "0"
|
||
|
|
sec ;[5]
|
||
|
|
ror shift ;[6] shift "1" into the data
|
||
|
|
brcs b6checkUnstuff ;[7] When after shift C is set, next bit is bit7
|
||
|
|
nop2 ;[8]
|
||
|
|
dec bitcnt ;[10]
|
||
|
|
brne bitloop ;[11]
|
||
|
|
ldi x1,0 ;[12] indicate unstuff for bit other than bit6 or bit7
|
||
|
|
in bitcnt, USBIN ;[0] sample stuff bit
|
||
|
|
rjmp unstuff ;[1]
|
||
|
|
|
||
|
|
handle0:
|
||
|
|
mov x2, x1 ;[6] Set x2 to current line state
|
||
|
|
ldi bitcnt, 6 ;[7] reset unstuff counter.
|
||
|
|
lsr shift ;[8] shift "0" into the data
|
||
|
|
brcs bit7 ;[9] When after shift C is set, next bit is bit7
|
||
|
|
nop ;[10]
|
||
|
|
rjmp bitloop ;[11]
|
||
|
|
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
; End of receive loop. Now start handling EOP
|
||
|
|
;----------------------------------------------------------------------------
|
||
|
|
|
||
|
|
macro POP_STANDARD ; 14 cycles
|
||
|
|
pop cnt
|
||
|
|
pop x4
|
||
|
|
pop x3
|
||
|
|
pop x2
|
||
|
|
pop x1
|
||
|
|
pop shift
|
||
|
|
pop bitcnt
|
||
|
|
endm
|
||
|
|
macro POP_RETI ; 7 cycles
|
||
|
|
pop YH
|
||
|
|
pop YL
|
||
|
|
out SREG, YL
|
||
|
|
pop YL
|
||
|
|
endm
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
#include "asmcommon.inc"
|
||
|
|
|
||
|
|
; USB spec says:
|
||
|
|
; idle = J
|
||
|
|
; J = (D+ = 0), (D- = 1)
|
||
|
|
; K = (D+ = 1), (D- = 0)
|
||
|
|
; Spec allows 7.5 bit times from EOP to SOP for replies
|
||
|
|
; 7.5 bit times is 100 cycles. This implementation arrives a bit later at se0
|
||
|
|
; then specified in the include file but there is plenty of time
|
||
|
|
|
||
|
|
bitstuffN:
|
||
|
|
eor x1, x4 ;[8]
|
||
|
|
ldi x2, 0 ;[9]
|
||
|
|
nop2 ;[10]
|
||
|
|
out USBOUT, x1 ;[12] <-- out
|
||
|
|
rjmp didStuffN ;[0]
|
||
|
|
|
||
|
|
bitstuff7:
|
||
|
|
eor x1, x4 ;[6]
|
||
|
|
ldi x2, 0 ;[7] Carry is zero due to brcc
|
||
|
|
rol shift ;[8] compensate for ror shift at branch destination
|
||
|
|
nop2 ;[9]
|
||
|
|
rjmp didStuff7 ;[11]
|
||
|
|
|
||
|
|
sendNakAndReti:
|
||
|
|
ldi x3, USBPID_NAK ;[-18]
|
||
|
|
rjmp sendX3AndReti ;[-17]
|
||
|
|
sendAckAndReti:
|
||
|
|
ldi cnt, USBPID_ACK ;[-17]
|
||
|
|
sendCntAndReti:
|
||
|
|
mov x3, cnt ;[-16]
|
||
|
|
sendX3AndReti:
|
||
|
|
ldi YL, 20 ;[-15] x3==r20 address is 20
|
||
|
|
ldi YH, 0 ;[-14]
|
||
|
|
ldi cnt, 2 ;[-13]
|
||
|
|
; rjmp usbSendAndReti fallthrough
|
||
|
|
|
||
|
|
;usbSend:
|
||
|
|
;pointer to data in 'Y'
|
||
|
|
;number of bytes in 'cnt' -- including sync byte [range 2 ... 12]
|
||
|
|
;uses: x1...x4, btcnt, shift, cnt, Y
|
||
|
|
;Numbers in brackets are time since first bit of sync pattern is sent
|
||
|
|
;We don't match the transfer rate exactly (don't insert leap cycles every third
|
||
|
|
;byte) because the spec demands only 1.5% precision anyway.
|
||
|
|
usbSendAndReti: ; 12 cycles until SOP
|
||
|
|
in x2, USBDDR ;[-12]
|
||
|
|
ori x2, USBMASK ;[-11]
|
||
|
|
sbi USBOUT, USBMINUS;[-10] prepare idle state; D+ and D- must have been 0 (no pullups)
|
||
|
|
in x1, USBOUT ;[-8] port mirror for tx loop
|
||
|
|
out USBDDR, x2 ;[-7] <- acquire bus
|
||
|
|
; need not init x2 (bitstuff history) because sync starts with 0
|
||
|
|
ldi x4, USBMASK ;[-6] exor mask
|
||
|
|
ldi shift, 0x80 ;[-5] sync byte is first byte sent
|
||
|
|
txByteLoop:
|
||
|
|
ldi bitcnt, 0x49 ;[-4] [10] binary 01001001
|
||
|
|
txBitLoop:
|
||
|
|
sbrs shift, 0 ;[-3] [10] [11]
|
||
|
|
eor x1, x4 ;[-2] [11] [12]
|
||
|
|
out USBOUT, x1 ;[-1] [12] [13] <-- out N
|
||
|
|
ror shift ;[0] [13] [14]
|
||
|
|
ror x2 ;[1]
|
||
|
|
didStuffN:
|
||
|
|
nop2 ;[2]
|
||
|
|
nop ;[4]
|
||
|
|
cpi x2, 0xfc ;[5]
|
||
|
|
brcc bitstuffN ;[6]
|
||
|
|
lsr bitcnt ;[7]
|
||
|
|
brcc txBitLoop ;[8]
|
||
|
|
brne txBitLoop ;[9]
|
||
|
|
|
||
|
|
sbrs shift, 0 ;[10]
|
||
|
|
eor x1, x4 ;[11]
|
||
|
|
didStuff7:
|
||
|
|
out USBOUT, x1 ;[-1] [13] <-- out 7
|
||
|
|
ror shift ;[0] [14]
|
||
|
|
ror x2 ;[1]
|
||
|
|
nop ;[2]
|
||
|
|
cpi x2, 0xfc ;[3]
|
||
|
|
brcc bitstuff7 ;[4]
|
||
|
|
ld shift, y+ ;[5]
|
||
|
|
dec cnt ;[7]
|
||
|
|
brne txByteLoop ;[8]
|
||
|
|
;make SE0:
|
||
|
|
cbr x1, USBMASK ;[9] prepare SE0 [spec says EOP may be 25 to 30 cycles]
|
||
|
|
lds x2, usbNewDeviceAddr;[10]
|
||
|
|
lsl x2 ;[12] we compare with left shifted address
|
||
|
|
out USBOUT, x1 ;[13] <-- out SE0 -- from now 2 bits = 22 cycles until bus idle
|
||
|
|
subi YL, 20 + 2 ;[0] Only assign address on data packets, not ACK/NAK in x3
|
||
|
|
sbci YH, 0 ;[1]
|
||
|
|
;2006-03-06: moved transfer of new address to usbDeviceAddr from C-Code to asm:
|
||
|
|
;set address only after data packet was sent, not after handshake
|
||
|
|
breq skipAddrAssign ;[2]
|
||
|
|
sts usbDeviceAddr, x2; if not skipped: SE0 is one cycle longer
|
||
|
|
skipAddrAssign:
|
||
|
|
;end of usbDeviceAddress transfer
|
||
|
|
ldi x2, 1<<USB_INTR_PENDING_BIT;[4] int0 occurred during TX -- clear pending flag
|
||
|
|
USB_STORE_PENDING(x2) ;[5]
|
||
|
|
ori x1, USBIDLE ;[6]
|
||
|
|
in x2, USBDDR ;[7]
|
||
|
|
cbr x2, USBMASK ;[8] set both pins to input
|
||
|
|
mov x3, x1 ;[9]
|
||
|
|
cbr x3, USBMASK ;[10] configure no pullup on both pins
|
||
|
|
ldi x4, 5 ;[11]
|
||
|
|
se0Delay:
|
||
|
|
dec x4 ;[12] [15] [18] [21] [24]
|
||
|
|
brne se0Delay ;[13] [16] [19] [22] [25]
|
||
|
|
out USBOUT, x1 ;[26] <-- out J (idle) -- end of SE0 (EOP signal)
|
||
|
|
out USBDDR, x2 ;[27] <-- release bus now
|
||
|
|
out USBOUT, x3 ;[28] <-- ensure no pull-up resistors are active
|
||
|
|
rjmp doReturn
|