forked from forks/qmk_firmware
92 lines
3.2 KiB
C
92 lines
3.2 KiB
C
/**
|
|
* Copyright 2021 Charly Delay <charly@codesink.dev> (@0xcharly)
|
|
*
|
|
* This program is free software: you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License as published by
|
|
* the Free Software Foundation, either version 2 of the License, or
|
|
* (at your option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful,
|
|
* but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
* GNU General Public License for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#pragma once
|
|
|
|
#undef MATRIX_COL_PINS
|
|
#define MATRIX_COL_PINS \
|
|
{ B0, B1, B10, B3, B4, B5 }
|
|
#undef MATRIX_COL_PINS_RIGHT
|
|
#define MATRIX_COL_PINS_RIGHT \
|
|
{ B0, B1, B10, B3, B4, B5 }
|
|
|
|
#undef MATRIX_ROW_PINS
|
|
#define MATRIX_ROW_PINS \
|
|
{ B15, A2, B8, A8, B9 }
|
|
#undef MATRIX_ROW_PINS_RIGHT
|
|
#define MATRIX_ROW_PINS_RIGHT \
|
|
{ B15, A2, B8, A8, B9 }
|
|
|
|
#define DIODE_DIRECTION ROW2COL
|
|
#define SPLIT_HAND_PIN A3
|
|
|
|
#undef RGB_DI_PIN
|
|
#define RGB_DI_PIN A1
|
|
#define WS2812_EXTERNAL_PULLUP
|
|
#define WS2812_PWM_DRIVER PWMD2
|
|
#define WS2812_PWM_CHANNEL 2
|
|
#define WS2812_PWM_PAL_MODE 1
|
|
#define WS2812_EXTERNAL_PULLUP
|
|
#define WS2812_DMA_STREAM STM32_DMA1_STREAM1
|
|
#define WS2812_DMA_CHANNEL 3
|
|
#define WS2812_PWM_TARGET_PERIOD 800000
|
|
|
|
#define DEBUG_LED_PIN C13
|
|
|
|
#undef SOFT_SERIAL_PIN
|
|
// #define SERIAL_USART_FULL_DUPLEX // Enable full duplex operation mode.
|
|
#define SERIAL_USART_TX_PIN A9
|
|
// #define SERIAL_USART_RX_PIN A3
|
|
// #define SERIAL_USART_DRIVER SD2
|
|
// #define SERIAL_USART_TX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
|
|
// #define SERIAL_USART_RX_PAL_MODE 7 // Pin "alternate function", see the respective datasheet for the appropriate values for your MCU. default: 7
|
|
// #define SERIAL_USART_TIMEOUT 100 // USART driver timeout. default 100
|
|
// // #define SERIAL_USART_PIN_SWAP // swap RX and TX pins on master
|
|
// // To use the highest possible baudrate (3.75Mbit/s) uncomment the following
|
|
// // line, this can result in dropped communications so lower the speed if there
|
|
// // are many timeouts.
|
|
// // #define SERIAL_USART_SPEED (STM32_PCLK2 >> 4)
|
|
|
|
#define CRC8_USE_TABLE
|
|
#define CRC8_OPTIMIZE_SPEED
|
|
|
|
/* spi config for eeprom and pmw3360 sensor */
|
|
#define SPI_DRIVER SPID1
|
|
#define SPI_SCK_PIN A5
|
|
#define SPI_SCK_PAL_MODE 5
|
|
#define SPI_MOSI_PIN A7
|
|
#define SPI_MOSI_PAL_MODE 5
|
|
#define SPI_MISO_PIN A6
|
|
#define SPI_MISO_PAL_MODE 5
|
|
|
|
#define EXTERNAL_EEPROM_SPI_SLAVE_SELECT_PIN A4
|
|
#define EXTERNAL_EEPROM_SPI_CLOCK_DIVISOR 64
|
|
|
|
#undef PMW3360_CS_PIN
|
|
#define PMW3360_CS_PIN B14
|
|
#define PMW3360_CS_MODE 3
|
|
#define PMW3360_CS_DIVISOR 64
|
|
|
|
#define CHARYBDIS_MINIMUM_DEFAULT_DPI 1200
|
|
#define CHARYBDIS_DEFAULT_DPI_CONFIG_STEP 400
|
|
#define CHARYBDIS_MINIMUM_SNIPING_DPI 200
|
|
#define CHARYBDIS_SNIPING_DPI_CONFIG_STEP 100
|
|
|
|
/* RGB Matrix. */
|
|
|
|
#undef RGB_MATRIX_MAXIMUM_BRIGHTNESS
|
|
#define RGB_MATRIX_MAXIMUM_BRIGHTNESS 150
|