qmk_firmware/platforms/avr/drivers/serial.c

/*
 * WARNING: be careful changing this code, it is very timing dependent
 *
 * 2018-10-28 checked
 *  avr-gcc 4.9.2
 *  avr-gcc 5.4.0
 *  avr-gcc 7.3.0
 */

#ifndef F_CPU
#    define F_CPU 16000000
#endif

#include <avr/io.h>
#include <avr/interrupt.h>
#include <util/delay.h>
#include <stddef.h>
#include <stdbool.h>
#include "gpio.h"
#include "serial.h"

#ifdef SOFT_SERIAL_PIN

#    if !(defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB647__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__) || defined(__AVR_AT90USB162__) || defined(__AVR_ATmega16U2__) || defined(__AVR_ATmega32U2__) || defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__))
#        error serial.c is not supported for the currently selected MCU
#    endif
// if using ATmega32U4/2, AT90USBxxx I2C, can not use PD0 and PD1 in soft serial.
#    if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__) || defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB647__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__)
#        if defined(USE_AVR_I2C) && (SOFT_SERIAL_PIN == D0 || SOFT_SERIAL_PIN == D1)
#            error Using I2C, so can not use PD0, PD1
#        endif
#    endif
// PD0..PD3, common config
#    if SOFT_SERIAL_PIN == D0
#        define EIMSK_BIT _BV(INT0)
#        define EICRx_BIT (~(_BV(ISC00) | _BV(ISC01)))
#        define SERIAL_PIN_INTERRUPT INT0_vect
#        define EICRx EICRA
#    elif SOFT_SERIAL_PIN == D1
#        define EIMSK_BIT _BV(INT1)
#        define EICRx_BIT (~(_BV(ISC10) | _BV(ISC11)))
#        define SERIAL_PIN_INTERRUPT INT1_vect
#        define EICRx EICRA
#    elif SOFT_SERIAL_PIN == D2
#        define EIMSK_BIT _BV(INT2)
#        define EICRx_BIT (~(_BV(ISC20) | _BV(ISC21)))
#        define SERIAL_PIN_INTERRUPT INT2_vect
#        define EICRx EICRA
#    elif SOFT_SERIAL_PIN == D3
#        define EIMSK_BIT _BV(INT3)
#        define EICRx_BIT (~(_BV(ISC30) | _BV(ISC31)))
#        define SERIAL_PIN_INTERRUPT INT3_vect
#        define EICRx EICRA
#    endif

// ATmegaxxU2/AT90USB162 specific config
#    if defined(__AVR_ATmega16U2__) || defined(__AVR_ATmega32U2__) || defined(__AVR_AT90USB162__)
// PD4(INT5), PD6(INT6), PD7(INT7), PC7(INT4)
#        if SOFT_SERIAL_PIN == D4
#            define EIMSK_BIT _BV(INT5)
#            define EICRx_BIT (~(_BV(ISC50) | _BV(ISC51)))
#            define SERIAL_PIN_INTERRUPT INT5_vect
#            define EICRx EICRB
#        elif SOFT_SERIAL_PIN == D6
#            define EIMSK_BIT _BV(INT6)
#            define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61)))
#            define SERIAL_PIN_INTERRUPT INT6_vect
#            define EICRx EICRB
#        elif SOFT_SERIAL_PIN == D7
#            define EIMSK_BIT _BV(INT7)
#            define EICRx_BIT (~(_BV(ISC70) | _BV(ISC71)))
#            define SERIAL_PIN_INTERRUPT INT7_vect
#            define EICRx EICRB
#        elif SOFT_SERIAL_PIN == C7
#            define EIMSK_BIT _BV(INT4)
#            define EICRx_BIT (~(_BV(ISC40) | _BV(ISC41)))
#            define SERIAL_PIN_INTERRUPT INT4_vect
#            define EICRx EICRB
#        endif
#    endif

// ATmegaxxU4 specific config
#    if defined(__AVR_ATmega16U4__) || defined(__AVR_ATmega32U4__)
// PE6(INT6)
#        if SOFT_SERIAL_PIN == E6
#            define EIMSK_BIT _BV(INT6)
#            define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61)))
#            define SERIAL_PIN_INTERRUPT INT6_vect
#            define EICRx EICRB
#        endif
#    endif

// AT90USBxxx specific config
#    if defined(__AVR_AT90USB646__) || defined(__AVR_AT90USB647__) || defined(__AVR_AT90USB1286__) || defined(__AVR_AT90USB1287__)
// PE4..PE7(INT4..INT7)
#        if SOFT_SERIAL_PIN == E4
#            define EIMSK_BIT _BV(INT4)
#            define EICRx_BIT (~(_BV(ISC40) | _BV(ISC41)))
#            define SERIAL_PIN_INTERRUPT INT4_vect
#            define EICRx EICRB
#        elif SOFT_SERIAL_PIN == E5
#            define EIMSK_BIT _BV(INT5)
#            define EICRx_BIT (~(_BV(ISC50) | _BV(ISC51)))
#            define SERIAL_PIN_INTERRUPT INT5_vect
#            define EICRx EICRB
#        elif SOFT_SERIAL_PIN == E6
#            define EIMSK_BIT _BV(INT6)
#            define EICRx_BIT (~(_BV(ISC60) | _BV(ISC61)))
#            define SERIAL_PIN_INTERRUPT INT6_vect
#            define EICRx EICRB
#        elif SOFT_SERIAL_PIN == E7
#            define EIMSK_BIT _BV(INT7)
#            define EICRx_BIT (~(_BV(ISC70) | _BV(ISC71)))
#            define SERIAL_PIN_INTERRUPT INT7_vect
#            define EICRx EICRB
#        endif
#    endif

#    ifndef SERIAL_PIN_INTERRUPT
#        error invalid SOFT_SERIAL_PIN value
#    endif

#    define ALWAYS_INLINE __attribute__((always_inline))
#    define NO_INLINE __attribute__((noinline))
#    define _delay_sub_us(x) __builtin_avr_delay_cycles(x)

// parity check
#    define ODD_PARITY 1
#    define EVEN_PARITY 0
#    define PARITY EVEN_PARITY

#    ifdef SERIAL_DELAY
// custom setup in config.h
// #define TID_SEND_ADJUST 2
// #define SERIAL_DELAY 6             // micro sec
// #define READ_WRITE_START_ADJUST 30 // cycles
// #define READ_WRITE_WIDTH_ADJUST 8 // cycles
#    else
// ============ Standard setups ============

#        ifndef SELECT_SOFT_SERIAL_SPEED
#            define SELECT_SOFT_SERIAL_SPEED 1
//  0: about 189kbps (Experimental only)
//  1: about 137kbps (default)
//  2: about 75kbps
//  3: about 39kbps
//  4: about 26kbps
//  5: about 20kbps
#        endif

#        if __GNUC__ < 6
#            define TID_SEND_ADJUST 14
#        else
#            define TID_SEND_ADJUST 2
#        endif

#        if SELECT_SOFT_SERIAL_SPEED == 0
// Very High speed
#            define SERIAL_DELAY 4 // micro sec
#            if __GNUC__ < 6
#                define READ_WRITE_START_ADJUST 33 // cycles
#                define READ_WRITE_WIDTH_ADJUST 3  // cycles
#            else
#                define READ_WRITE_START_ADJUST 34 // cycles
#                define READ_WRITE_WIDTH_ADJUST 7  // cycles
#            endif
#        elif SELECT_SOFT_SERIAL_SPEED == 1
// High speed
#            define SERIAL_DELAY 6 // micro sec
#            if __GNUC__ < 6
#                define READ_WRITE_START_ADJUST 30 // cycles
#                define READ_WRITE_WIDTH_ADJUST 3  // cycles
#            else
#                define READ_WRITE_START_ADJUST 33 // cycles
#                define READ_WRITE_WIDTH_ADJUST 7  // cycles
#            endif
#        elif SELECT_SOFT_SERIAL_SPEED == 2
// Middle speed
#            define SERIAL_DELAY 12            // micro sec
#            define READ_WRITE_START_ADJUST 30 // cycles
#            if __GNUC__ < 6
#                define READ_WRITE_WIDTH_ADJUST 3 // cycles
#            else
#                define READ_WRITE_WIDTH_ADJUST 7 // cycles
#            endif
#        elif SELECT_SOFT_SERIAL_SPEED == 3
// Low speed
#            define SERIAL_DELAY 24            // micro sec
#            define READ_WRITE_START_ADJUST 30 // cycles
#            if __GNUC__ < 6
#                define READ_WRITE_WIDTH_ADJUST 3 // cycles
#            else
#                define READ_WRITE_WIDTH_ADJUST 7 // cycles
#            endif
#        elif SELECT_SOFT_SERIAL_SPEED == 4
// Very Low speed
#            define SERIAL_DELAY 36            // micro sec
#            define READ_WRITE_START_ADJUST 30 // cycles
#            if __GNUC__ < 6
#                define READ_WRITE_WIDTH_ADJUST 3 // cycles
#            else
#                define READ_WRITE_WIDTH_ADJUST 7 // cycles
#            endif
#        elif SELECT_SOFT_SERIAL_SPEED == 5
// Ultra Low speed
#            define SERIAL_DELAY 48            // micro sec
#            define READ_WRITE_START_ADJUST 30 // cycles
#            if __GNUC__ < 6
#                define READ_WRITE_WIDTH_ADJUST 3 // cycles
#            else
#                define READ_WRITE_WIDTH_ADJUST 7 // cycles
#            endif
#        else
#            error invalid SELECT_SOFT_SERIAL_SPEED value
#        endif /* SELECT_SOFT_SERIAL_SPEED */
#    endif     /* SERIAL_DELAY */

#    define SERIAL_DELAY_HALF1 (SERIAL_DELAY / 2)
#    define SERIAL_DELAY_HALF2 (SERIAL_DELAY - SERIAL_DELAY / 2)

#    define SLAVE_INT_WIDTH_US 1
#    define SLAVE_INT_ACK_WIDTH_UNIT 2
#    define SLAVE_INT_ACK_WIDTH 4

inline static void serial_delay(void) ALWAYS_INLINE;
inline static void serial_delay(void) {
    _delay_us(SERIAL_DELAY);
}

inline static void serial_delay_half1(void) ALWAYS_INLINE;
inline static void serial_delay_half1(void) {
    _delay_us(SERIAL_DELAY_HALF1);
}

inline static void serial_delay_half2(void) ALWAYS_INLINE;
inline static void serial_delay_half2(void) {
    _delay_us(SERIAL_DELAY_HALF2);
}

inline static void serial_output(void) ALWAYS_INLINE;
inline static void serial_output(void) {
    setPinOutput(SOFT_SERIAL_PIN);
}

// make the serial pin an input with pull-up resistor
inline static void serial_input_with_pullup(void) ALWAYS_INLINE;
inline static void serial_input_with_pullup(void) {
    setPinInputHigh(SOFT_SERIAL_PIN);
}

inline static uint8_t serial_read_pin(void) ALWAYS_INLINE;
inline static uint8_t serial_read_pin(void) {
    return !!readPin(SOFT_SERIAL_PIN);
}

inline static void serial_low(void) ALWAYS_INLINE;
inline static void serial_low(void) {
    writePinLow(SOFT_SERIAL_PIN);
}

inline static void serial_high(void) ALWAYS_INLINE;
inline static void serial_high(void) {
    writePinHigh(SOFT_SERIAL_PIN);
}

void soft_serial_initiator_init(void) {
    serial_output();
    serial_high();
}

void soft_serial_target_init(void) {
    serial_input_with_pullup();

    // Enable INT0-INT7
    EIMSK |= EIMSK_BIT;
    EICRx &= EICRx_BIT;
}

// Used by the sender to synchronize timing with the reciver.
static void sync_recv(void) NO_INLINE;
static void sync_recv(void) {
    for (uint8_t i = 0; i < SERIAL_DELAY * 5 && serial_read_pin(); i++) {
    }
    // This shouldn't hang if the target disconnects because the
    // serial line will float to high if the target does disconnect.
    while (!serial_read_pin())
        ;
}

// Used by the reciver to send a synchronization signal to the sender.
static void sync_send(void) NO_INLINE;
static void sync_send(void) {
    serial_low();
    serial_delay();
    serial_high();
}

// Reads a byte from the serial line
static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) NO_INLINE;
static uint8_t serial_read_chunk(uint8_t *pterrcount, uint8_t bit) {
    uint8_t byte, i, p, pb;

    _delay_sub_us(READ_WRITE_START_ADJUST);
    for (i = 0, byte = 0, p = PARITY; i < bit; i++) {
        serial_delay_half1(); // read the middle of pulses
        if (serial_read_pin()) {
            byte = (byte << 1) | 1;
            p ^= 1;
        } else {
            byte = (byte << 1) | 0;
            p ^= 0;
        }
        _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
        serial_delay_half2();
    }
    /* recive parity bit */
    serial_delay_half1(); // read the middle of pulses
    pb = serial_read_pin();
    _delay_sub_us(READ_WRITE_WIDTH_ADJUST);
    serial_delay_half2();

    *pterrcount += (p != pb) ? 1 : 0;

    return byte;
}

// Sends a byte with MSB ordering
void serial_write_chunk(uint8_t data, uint8_t bit) NO_INLINE;
void serial_write_chunk(uint8_t data, uint8_t bit) {
    uint8_t b, p;
    for (p = PARITY, b = 1 << (bit - 1); b; b >>= 1) {
        if (data & b) {
            serial_high();
            p ^= 1;
        } else {
            serial_low();
            p ^= 0;
        }
        serial_delay();
    }
    /* send parity bit */
    if (p & 1) {
        serial_high();
    } else {
        serial_low();
    }
    serial_delay();

    serial_low(); // sync_send() / senc_recv() need raise edge
}

static void serial_send_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
static void serial_send_packet(uint8_t *buffer, uint8_t size) {
    for (uint8_t i = 0; i < size; ++i) {
        uint8_t data;
        data = buffer[i];
        sync_send();
        serial_write_chunk(data, 8);
    }
}

static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) NO_INLINE;
static uint8_t serial_recive_packet(uint8_t *buffer, uint8_t size) {
    uint8_t pecount = 0;
    for (uint8_t i = 0; i < size; ++i) {
        uint8_t data;
        sync_recv();
        data      = serial_read_chunk(&pecount, 8);
        buffer[i] = data;
    }
    return pecount == 0;
}

inline static void change_sender2reciver(void) {
    sync_send();                // 0
    serial_delay_half1();       // 1
    serial_low();               // 2
    serial_input_with_pullup(); // 2
    serial_delay_half1();       // 3
}

inline static void change_reciver2sender(void) {
    sync_recv();          // 0
    serial_delay();       // 1
    serial_low();         // 3
    serial_output();      // 3
    serial_delay_half1(); // 4
}

static inline uint8_t nibble_bits_count(uint8_t bits) {
    bits = (bits & 0x5) + (bits >> 1 & 0x5);
    bits = (bits & 0x3) + (bits >> 2 & 0x3);
    return bits;
}

// interrupt handle to be used by the target device
ISR(SERIAL_PIN_INTERRUPT) {
    // recive transaction table index
    uint8_t tid, bits;
    uint8_t pecount = 0;
    sync_recv();
    bits = serial_read_chunk(&pecount, 8);
    tid  = bits >> 3;
    bits = (bits & 7) != (nibble_bits_count(tid) & 7);
    if (bits || pecount > 0 || tid > NUM_TOTAL_TRANSACTIONS) {
        return;
    }
    serial_delay_half1();

    serial_high(); // response step1 low->high
    serial_output();
    _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT * SLAVE_INT_ACK_WIDTH);
    split_transaction_desc_t *trans = &split_transaction_table[tid];
    serial_low(); // response step2 ack high->low

    // If the transaction has a callback, we can execute it now
    if (trans->slave_callback) {
        trans->slave_callback(trans->initiator2target_buffer_size, split_trans_initiator2target_buffer(trans), trans->target2initiator_buffer_size, split_trans_target2initiator_buffer(trans));
    }

    // target send phase
    if (trans->target2initiator_buffer_size > 0) serial_send_packet((uint8_t *)split_trans_target2initiator_buffer(trans), trans->target2initiator_buffer_size);
    // target switch to input
    change_sender2reciver();

    // target recive phase
    if (trans->initiator2target_buffer_size > 0) {
        serial_recive_packet((uint8_t *)split_trans_initiator2target_buffer(trans), trans->initiator2target_buffer_size);
    }

    sync_recv(); // weit initiator output to high
}

/////////
//  start transaction by initiator
//
// bool  soft_serial_transaction(int sstd_index)
//
// this code is very time dependent, so we need to disable interrupts
bool soft_serial_transaction(int sstd_index) {
    if (sstd_index > NUM_TOTAL_TRANSACTIONS) return false;
    split_transaction_desc_t *trans = &split_transaction_table[sstd_index];

    cli();

    // signal to the target that we want to start a transaction
    serial_output();
    serial_low();
    _delay_us(SLAVE_INT_WIDTH_US);

    // send transaction table index
    int tid = (sstd_index << 3) | (7 & nibble_bits_count(sstd_index));
    sync_send();
    _delay_sub_us(TID_SEND_ADJUST);
    serial_write_chunk(tid, 8);
    serial_delay_half1();

    // wait for the target response (step1 low->high)
    serial_input_with_pullup();
    while (!serial_read_pin()) {
        _delay_sub_us(2);
    }

    // check if the target is present (step2 high->low)
    for (int i = 0; serial_read_pin(); i++) {
        if (i > SLAVE_INT_ACK_WIDTH + 1) {
            // slave failed to pull the line low, assume not present
            serial_output();
            serial_high();
            sei();
            return false;
        }
        _delay_sub_us(SLAVE_INT_ACK_WIDTH_UNIT);
    }

    // initiator recive phase
    // if the target is present syncronize with it
    if (trans->target2initiator_buffer_size > 0) {
        if (!serial_recive_packet((uint8_t *)split_trans_target2initiator_buffer(trans), trans->target2initiator_buffer_size)) {
            serial_output();
            serial_high();
            sei();
            return false;
        }
    }

    // initiator switch to output
    change_reciver2sender();

    // initiator send phase
    if (trans->initiator2target_buffer_size > 0) {
        serial_send_packet((uint8_t *)split_trans_initiator2target_buffer(trans), trans->initiator2target_buffer_size);
    }

    // always, release the line when not in use
    sync_send();

    sei();
    return true;
}
#else
#    ifndef USE_I2C
#        error SOFT_SERIAL_PIN or USE_I2C is required but has not been defined.
#    endif
#endif

// Helix serial.c history
//   2018-1-29 fork from let's split and add PD2, modify sync_recv() (#2308, bceffdefc)
//   2018-6-28 bug fix master to slave comm and speed up (#3255, 1038bbef4)
//             (adjusted with avr-gcc 4.9.2)
//   2018-7-13 remove USE_SERIAL_PD2 macro (#3374, f30d6dd78)
//             (adjusted with avr-gcc 4.9.2)
//   2018-8-11 add support multi-type transaction (#3608, feb5e4aae)
//             (adjusted with avr-gcc 4.9.2)
//   2018-10-21 fix serial and RGB animation conflict (#4191, 4665e4fff)
//             (adjusted with avr-gcc 7.3.0)
//   2018-10-28 re-adjust compiler depend value of delay (#4269, 8517f8a66)
//             (adjusted with avr-gcc 5.4.0, 7.3.0)
//   2018-12-17 copy to TOP/quantum/split_common/ and remove backward compatibility code (#4669)