forked from forks/qmk_firmware
6cccc22be9
Using QUANTUM_LIB_SRC prevents the warning when multiple sources add the i2c_master.c file. Boards such as the Ergodox EZ Glow see this warning every time they compile because the board uses the file in general, and because the RGB LED Matrix requires it, as well.
90 lines
3.4 KiB
Makefile
90 lines
3.4 KiB
Makefile
#----------------------------------------------------------------------------
|
|
# On command line:
|
|
#
|
|
# make = Make software.
|
|
#
|
|
# make clean = Clean out built project files.
|
|
#
|
|
# That's pretty much all you need. To compile, always go make clean,
|
|
# followed by make.
|
|
#
|
|
# For advanced users only:
|
|
# make teensy = Download the hex file to the device, using teensy_loader_cli.
|
|
# (must have teensy_loader_cli installed).
|
|
#
|
|
#----------------------------------------------------------------------------
|
|
|
|
# # project specific files
|
|
SRC += matrix.c
|
|
QUANTUM_LIB_SRC += i2c_master.c
|
|
|
|
# MCU name
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Bootloader
|
|
# This definition is optional, and if your keyboard supports multiple bootloaders of
|
|
# different sizes, comment this out, and the correct address will be loaded
|
|
# automatically (+60). See bootloader.mk for all options.
|
|
BOOTLOADER = halfkay
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
# If you have Left LEDs (see
|
|
# https://geekhack.org/index.php?topic=22780.msg873819#msg873819 for
|
|
# details), include the following define:
|
|
# OPT_DEFS += -DLEFT_LEDS
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE = no # Console for debug(+400)
|
|
COMMAND_ENABLE = yes # Commands for debug and configuration
|
|
CUSTOM_MATRIX = yes # Custom matrix file for the ErgoDox EZ
|
|
NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
|
|
UNICODE_ENABLE = yes # Unicode
|
|
SWAP_HANDS_ENABLE= yes # Allow swapping hands of keyboard
|
|
SLEEP_LED_ENABLE = no
|
|
API_SYSEX_ENABLE = no
|
|
RGBLIGHT_ENABLE = yes
|
|
RGB_MATRIX_ENABLE = no # enable later
|
|
DEBOUNCE_TYPE = eager_pr
|
|
|
|
LAYOUTS = ergodox
|