forked from forks/qmk_firmware
7960302242
* copied mjt keymaps from archive * All mjt boards now compile * fixed jd45-mjt breathing * Updates to fix SpaceFN but not tested yet. * Still missing either spacebar or an adjacent keypress. * Debugging rigged up for use with hid_listen. * Reverted the default keymap to use tap_layer_key rather than custom. Moved custom approach to keymap_debug.c * Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function. * Cleaned up JD45 keymap that uses tapkey. * Redid minivan keymap with numsym rather than raise/lower. Untested. * Created my MJT keymap for HHKB Enabled dynamic macros and moved somoe of the shortcuts around. * Minor keymap fixes to make them compile without errors. * Added home/end to right arrow cluster on DYN layer. * Added more keys to fn and dyn layers. * It wasn't using my custom layer last time somehow...? Now it will. * Compiled and installed at end of day on 8/23 * Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback. * Fixed volume controls... were reversed and disabled. * Added F13-F15 back to fkeys layer in Minivan * Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan. * Removed DYN layer. * Fixed diagram in planck numsym. * Cleanup for pull request. * Roadkit flip phone warning. * Replaced PLAY_NOTES_ARRAY to PLAY_SONG * reset the submodules * checked out specific commits for submodules * Removed debugging from JD45 shared config.h * Moved custom rules.mk to apropriate keymap Reset the shared rules.mk file. * Trailing return issue in rules.mk Gotta make for a smooth pull request :-)
68 lines
2.6 KiB
Makefile
68 lines
2.6 KiB
Makefile
|
|
|
|
# MCU name
|
|
#MCU = at90usb1287
|
|
MCU = atmega32u4
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
|
|
#
|
|
# LUFA specific
|
|
#
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
# Interrupt driven control endpoint task(+60)
|
|
OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT
|
|
|
|
|
|
# Boot Section Size in *bytes*
|
|
# Teensy halfKay 512
|
|
# Teensy++ halfKay 1024
|
|
# Atmel DFU loader 4096
|
|
# LUFA bootloader 4096
|
|
# USBaspLoader 2048
|
|
OPT_DEFS += -DBOOTLOADER_SIZE=4096
|
|
|
|
|
|
# Build Options
|
|
# comment out to disable the options.
|
|
#
|
|
BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000)
|
|
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
|
|
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
|
|
CONSOLE_ENABLE = yes # Console for debug(+400)
|
|
COMMAND_ENABLE = yes # Commands for debug and configuration
|
|
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
|
|
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
|
|
NKRO_ENABLE = yes # USB Nkey Rollover - not yet supported in LUFA
|
|
BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality
|
|
MIDI_ENABLE = no # MIDI controls
|
|
# UNICODE_ENABLE = YES # Unicode
|
|
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
|