forked from forks/qmk_firmware
81 lines
2.3 KiB
Plaintext
81 lines
2.3 KiB
Plaintext
Alternative Controller for HHKB
|
|
===============================
|
|
|
|
Feature
|
|
-------
|
|
- Mouse Keys
|
|
- NKRO on USB
|
|
- Keymap Layers
|
|
|
|
|
|
Customize Keymap
|
|
----------------
|
|
see keymap.c.
|
|
|
|
|
|
Build for Teensy
|
|
----------------
|
|
0. Edit matrix.c.
|
|
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
|
|
1. Define macros in config_pjrc.h.(Optional)
|
|
VENDOR_ID, PRODUCT_ID and string descriptor.
|
|
IS_COMMAND
|
|
2. Edit Makefile for MCU setting and build options.
|
|
MCU, F_CPU
|
|
MOUSEKEY_ENABLE, USB_EXTRA_ENABLE, USB_NKRO_ENABLE
|
|
3. Build hex file.
|
|
$ make
|
|
4. Program MCU.
|
|
$ make program
|
|
|
|
|
|
Build for V-USB
|
|
---------------
|
|
0. Edit matrix.c and usbconfig.h.
|
|
adjust scan code to your pin configuration.(see doc/HHKB.txt for pinouts)
|
|
define macros for V-USB in usbconfig.h.
|
|
1. Define macros in config_vusb.h.(Optional)
|
|
IS_COMMAND
|
|
2. Edit Makefile.vusb for MCU setting and build options.
|
|
MCU, F_CPU
|
|
MOUSEKEY_ENABLE, USB_EXTRA_ENABLE, USB_NKRO_ENABLE
|
|
3. Build hex file.
|
|
$ make -f Makefile.vusb
|
|
4. Program MCU.
|
|
$ make -f Makefile.vusb program
|
|
|
|
Using a bootloader to program for convenience is recommended.
|
|
Once program this V-USB bootloader at first, you can program MCU without
|
|
extra programmer. You should have reset switch to start up as bootloader
|
|
mode in this case.
|
|
USBaspLoader:
|
|
http://www.obdev.at/products/vusb/usbasploader.html
|
|
|
|
|
|
V-USB Circuit
|
|
-------------
|
|
+---+ +---------------+
|
|
USB GND | | ATmega168 |
|
|
=== C3 | |
|
|
5V <-------+--------+---|Vcc,AVCC | HHKB
|
|
R1 | | ====
|
|
D- <----+--+-----R2-----|INT1 PB0-2|------->ROW
|
|
D+ <----|---+----R3-----|INT0 PB3-5|------->COL
|
|
Z1 Z2 | PB6|------->ENABLE
|
|
GND<----+---+--+--+-----|GND PE6|------->KEY
|
|
| | | PE7|------->PREV
|
|
| C2-+--|XTAL1 | (see doc/HHKB.txt for pinouts)
|
|
| X1 | |
|
|
+--C3-+--|XTAL2 RST|---SW--+GND
|
|
+---------------+
|
|
R1: 1.5K Ohm
|
|
R2,R3: 68 Ohm
|
|
Z1,Z2: Zener 3.6V
|
|
C1,C2: 22pF
|
|
C3: 0.1uF
|
|
X1: Crystal 20MHz(16MHz/12MHz)
|
|
SW: Push Switch(Optional for bootloader)
|
|
|
|
|
|
EOF
|