forked from forks/qmk_firmware
f698f1e3f4
* initial commit of budget96 * non logic changes * add my name to readme * update matrix.c * make the matrix representation of the layout macro * fix up LAYOUT macro * add missing character * initial keymap commit * put KC_NO where they belong * basic keymap * fix matrix row and col definition * The diagram I was sent and the pins used I was sent were in opposite order from each other. This should fix the issues * update the readme * change up manufacturer for budget96 * update copyright date * fix up the switch matrix and provide a keymap * forgot the keymap * other matrix fixes * missing a few keys in the switch matrix * messed up the row tracing * tweak keymap a bit * use a lower case k * fix spacing for markdown rendering * put in the reset key documentation * clean up the file a little * use LAYOUT_96_ansi * add a second layer for lighting controls * add in lighting support * add QMK Configurator support * use pragma once * remove un needed matrix.c * convert to GPIO methods * turn on rgblight_enable and get rid of custom matrix * set bootloadhid_bootloader to 1 * set bootmagic to lite and set it to k50 * add reset information to readme * use i2c_master instead of custom i2c * restore the custom i2c code * introduce reset key and eep_rst in function layer 1 * fix up pip3 install commands * fix up device and manufacturer names * remove un needed comments * add an ALL layout macro along with QMK Configurator support * move budget96 into donutcables directory since he actually has different boards * add a short donut cables blurb taken from his website * update readme for make instructions to point to the new path * Update keyboards/donutcables/budget96/config.h Co-Authored-By: mechmerlin <30334081+mechmerlin@users.noreply.github.com> * Update keyboards/donutcables/budget96/readme.md Co-Authored-By: mechmerlin <30334081+mechmerlin@users.noreply.github.com> * Update keyboards/donutcables/budget96/info.json Co-Authored-By: mechmerlin <30334081+mechmerlin@users.noreply.github.com> * turn on backlight * Update keyboards/donutcables/budget96/readme.md Co-Authored-By: mechmerlin <30334081+mechmerlin@users.noreply.github.com> * remove extra UART and BOOTLOADER settings that are not needed
107 lines
2.5 KiB
C
107 lines
2.5 KiB
C
/*
|
|
Copyright 2016 Luiz Ribeiro <luizribeiro@gmail.com>
|
|
|
|
This program is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 2 of the License, or
|
|
(at your option) any later version.
|
|
|
|
This program is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
// Please do not modify this file
|
|
|
|
#include <avr/io.h>
|
|
#include <util/twi.h>
|
|
|
|
#include "i2c.h"
|
|
|
|
void i2c_set_bitrate(uint16_t bitrate_khz) {
|
|
uint8_t bitrate_div = ((F_CPU / 1000l) / bitrate_khz);
|
|
if (bitrate_div >= 16) {
|
|
bitrate_div = (bitrate_div - 16) / 2;
|
|
}
|
|
TWBR = bitrate_div;
|
|
}
|
|
|
|
void i2c_init(void) {
|
|
// set pull-up resistors on I2C bus pins
|
|
PORTC |= 0b11;
|
|
|
|
i2c_set_bitrate(400);
|
|
|
|
// enable TWI (two-wire interface)
|
|
TWCR |= (1 << TWEN);
|
|
|
|
// enable TWI interrupt and slave address ACK
|
|
TWCR |= (1 << TWIE);
|
|
TWCR |= (1 << TWEA);
|
|
}
|
|
|
|
uint8_t i2c_start(uint8_t address) {
|
|
// reset TWI control register
|
|
TWCR = 0;
|
|
|
|
// begin transmission and wait for it to end
|
|
TWCR = (1<<TWINT) | (1<<TWSTA) | (1<<TWEN);
|
|
while (!(TWCR & (1<<TWINT)));
|
|
|
|
// check if the start condition was successfully transmitted
|
|
if ((TWSR & 0xF8) != TW_START) {
|
|
return 1;
|
|
}
|
|
|
|
// transmit address and wait
|
|
TWDR = address;
|
|
TWCR = (1<<TWINT) | (1<<TWEN);
|
|
while (!(TWCR & (1<<TWINT)));
|
|
|
|
// check if the device has acknowledged the READ / WRITE mode
|
|
uint8_t twst = TW_STATUS & 0xF8;
|
|
if ((twst != TW_MT_SLA_ACK) && (twst != TW_MR_SLA_ACK)) {
|
|
return 1;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
void i2c_stop(void) {
|
|
TWCR = (1<<TWINT) | (1<<TWEN) | (1<<TWSTO);
|
|
}
|
|
|
|
uint8_t i2c_write(uint8_t data) {
|
|
TWDR = data;
|
|
|
|
// transmit data and wait
|
|
TWCR = (1<<TWINT) | (1<<TWEN);
|
|
while (!(TWCR & (1<<TWINT)));
|
|
|
|
if ((TWSR & 0xF8) != TW_MT_DATA_ACK) {
|
|
return 1;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
uint8_t i2c_send(uint8_t address, uint8_t *data, uint16_t length) {
|
|
if (i2c_start(address)) {
|
|
return 1;
|
|
}
|
|
|
|
for (uint16_t i = 0; i < length; i++) {
|
|
if (i2c_write(data[i])) {
|
|
return 1;
|
|
}
|
|
}
|
|
|
|
i2c_stop();
|
|
|
|
return 0;
|
|
}
|