forked from forks/qmk_firmware
effa5914bf
- to make descriptor get VID/PID/Version from config.h. - remove keyboard out endpoint. Instead host can use control request.
161 lines
5 KiB
Makefile
161 lines
5 KiB
Makefile
# Hey Emacs, this is a -*- makefile -*-
|
|
#----------------------------------------------------------------------------
|
|
# WinAVR Makefile Template written by Eric B. Weddington, Jörg Wunsch, et al.
|
|
# >> Modified for use with the LUFA project. <<
|
|
#
|
|
# Released to the Public Domain
|
|
#
|
|
# Additional material for this makefile was written by:
|
|
# Peter Fleury
|
|
# Tim Henigan
|
|
# Colin O'Flynn
|
|
# Reiner Patommel
|
|
# Markus Pfaff
|
|
# Sander Pool
|
|
# Frederik Rouleau
|
|
# Carlos Lamas
|
|
# Dean Camera
|
|
# Opendous Inc.
|
|
# Denver Gingerich
|
|
#
|
|
#----------------------------------------------------------------------------
|
|
# On command line:
|
|
#
|
|
# make all = Make software.
|
|
#
|
|
# make clean = Clean out built project files.
|
|
#
|
|
# make coff = Convert ELF to AVR COFF.
|
|
#
|
|
# make extcoff = Convert ELF to AVR Extended COFF.
|
|
#
|
|
# make program = Download the hex file to the device, using avrdude.
|
|
# Please customize the avrdude settings below first!
|
|
#
|
|
# make dfu = Download the hex file to the device, using dfu-programmer (must
|
|
# have dfu-programmer installed).
|
|
#
|
|
# make flip = Download the hex file to the device, using Atmel FLIP (must
|
|
# have Atmel FLIP installed).
|
|
#
|
|
# make dfu-ee = Download the eeprom file to the device, using dfu-programmer
|
|
# (must have dfu-programmer installed).
|
|
#
|
|
# make flip-ee = Download the eeprom file to the device, using Atmel FLIP
|
|
# (must have Atmel FLIP installed).
|
|
#
|
|
# make doxygen = Generate DoxyGen documentation for the project (must have
|
|
# DoxyGen installed)
|
|
#
|
|
# make debug = Start either simulavr or avarice as specified for debugging,
|
|
# with avr-gdb or avr-insight as the front end for debugging.
|
|
#
|
|
# make filename.s = Just compile filename.c into the assembler code only.
|
|
#
|
|
# make filename.i = Create a preprocessed source file for use in submitting
|
|
# bug reports to the GCC project.
|
|
#
|
|
# To rebuild project do "make clean" then "make all".
|
|
#----------------------------------------------------------------------------
|
|
|
|
# Directory common source filess exist
|
|
TOP_DIR = ../..
|
|
|
|
# Directory keyboard dependent files exist
|
|
TARGET_DIR = .
|
|
|
|
# MCU name
|
|
#MCU = at90usb1287
|
|
MCU = atmega32u4
|
|
|
|
|
|
# Target architecture (see library "Board Types" documentation).
|
|
ARCH = AVR8
|
|
|
|
|
|
# Target board (see library "Board Types" documentation, NONE for projects not requiring
|
|
# LUFA board drivers). If USER is selected, put custom board drivers in a directory called
|
|
# "Board" inside the application directory.
|
|
BOARD = USBKEY
|
|
|
|
|
|
# Processor frequency.
|
|
# This will define a symbol, F_CPU, in all source code files equal to the
|
|
# processor frequency in Hz. You can then use this symbol in your source code to
|
|
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
|
|
# automatically to create a 32-bit value in your source code.
|
|
#
|
|
# This will be an integer division of F_USB below, as it is sourced by
|
|
# F_USB after it has run through any CPU prescalers. Note that this value
|
|
# does not *change* the processor frequency - it should merely be updated to
|
|
# reflect the processor speed set externally so that the code can use accurate
|
|
# software delays.
|
|
F_CPU = 16000000
|
|
|
|
|
|
# Input clock frequency.
|
|
# This will define a symbol, F_USB, in all source code files equal to the
|
|
# input clock frequency (before any prescaling is performed) in Hz. This value may
|
|
# differ from F_CPU if prescaling is used on the latter, and is required as the
|
|
# raw input clock is fed directly to the PLL sections of the AVR for high speed
|
|
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
|
|
# at the end, this will be done automatically to create a 32-bit value in your
|
|
# source code.
|
|
#
|
|
# If no clock division is performed on the input clock inside the AVR (via the
|
|
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
|
|
F_USB = $(F_CPU)
|
|
|
|
|
|
# Target file name (without extension).
|
|
TARGET = lufa
|
|
|
|
|
|
# Path to the LUFA library
|
|
LUFA_PATH = ../../protocol
|
|
|
|
# Create the LUFA source path variables by including the LUFA root makefile
|
|
include $(LUFA_PATH)/LUFA/makefile
|
|
|
|
|
|
|
|
# List C source files here. (C dependencies are automatically generated.)
|
|
LUFA_SRC = $(TARGET).c \
|
|
descriptor.c \
|
|
$(LUFA_SRC_USB) \
|
|
$(LUFA_SRC_USBCLASS)
|
|
|
|
SRC = $(subst $(LUFA_PATH)/LUFA/,,$(LUFA_SRC))
|
|
SRC += keymap.c \
|
|
matrix.c \
|
|
led.c
|
|
CONFIG_H = config.h
|
|
|
|
|
|
|
|
# LUFA library compile-time options and predefined tokens
|
|
LUFA_OPTS = -D USB_DEVICE_ONLY
|
|
LUFA_OPTS += -D FIXED_CONTROL_ENDPOINT_SIZE=8
|
|
LUFA_OPTS += -D FIXED_NUM_CONFIGURATIONS=1
|
|
LUFA_OPTS += -D USE_FLASH_DESCRIPTORS
|
|
LUFA_OPTS += -D USE_STATIC_OPTIONS="(USB_DEVICE_OPT_FULLSPEED | USB_OPT_REG_ENABLED | USB_OPT_AUTO_PLL)"
|
|
|
|
OPT_DEFS = -DF_CPU=$(F_CPU)UL
|
|
OPT_DEFS += -DF_USB=$(F_USB)UL
|
|
OPT_DEFS += -DBOARD=BOARD_$(BOARD) -DARCH=ARCH_$(ARCH)
|
|
OPT_DEFS += $(LUFA_OPTS)
|
|
|
|
|
|
|
|
# Search Path
|
|
VPATH += $(TARGET_DIR)
|
|
VPATH += $(LUFA_PATH)/LUFA
|
|
|
|
|
|
include $(TOP_DIR)/protocol.mk
|
|
include $(TOP_DIR)/common.mk
|
|
include $(TOP_DIR)/rules.mk
|
|
|
|
test:
|
|
echo $(SRC)
|