* Add VID/PIDs to ErgoDox EZ
* Add VID/PIDs for Planck EZ and Glow revision
* Make names consistent
* fix typo in docs
* Move LED config back, for maximum compatibility
* Add revisions for ErgoDox EZ boards
* Fix embarassing typo
* Typooooo
Co-authored-by: Nick Brassel <nick@tzarc.org>
* Update Licensing info
* Update Moonlander default keymap to match Oryx's default
* Fix formatting based on suggestions
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Make indicator LEDs more configurable
* Update default keymap
* Handle older eeprom settings
Co-authored-by: Nick Brassel <nick@tzarc.org>
Co-authored-by: James Young <18669334+noroadsleft@users.noreply.github.com>
* Convert ErgoDox EZ to lite matrix
* Add initial config from Dactyl config
Based on ErinCall's work to generalize the mcp i/o expander matrix code
* formatting
* Fix number of pins
* Remove unused defines
* Move Ergodox EZ RGB code to custom driver
Also implements full addressing of Ergodox EZ's LED Strip, as written by seebs
Co-authored-by: Seebs <seebs@seebs.net>
* Make Clipping range accessible for custom drivers
* Remove RGBW_BB_TWI from driver and docs
* Revert changes to clipping range support
* Use just rgblight_set instead of full custom driver
* Convert to i2c_master commands
* Rename rgblight driver and clean up includes
* Update Layer functions to use layer_state_t in ZSA Boards
* Update Music Mask for ZSA boards
Fixes an issue with the board getting stuck on Adjust layer when activating music mode
* Add Support for SMART LED Toggle to Planck EZ
* Add support for SMART LED toggle in Ergodox EZ
* Ifdef swiss cheeze for Oryx Configurator
* Documentation and updates
* Add Oryx Keymap
* Add option to configure the layers for the Layer Indicator
* Update keymap with better examples
* Make sure eeprom is initialized before reading from it
* Force flush of LED matrix when suspending board
This fixes an issue where the LEDs don't fully clear sometimes when the host system goes to sleep
* Enable RGB Sleeping by default
* Add clarification about planck ez led layer config
* Optimize RGB Matrix rendering for Ergodox EZ
* Optimize RGB Matrix rendering for Planck EZ
* Update keyboards/planck/ez/config.h
Co-Authored-By: Joel Challis <git@zvecr.com>
* clean up rgb matrix extern usage
Moved rgb matrix boiler plate into macros
Rebased onto typing heatmap pr
* Fixing the reversed frame buffer access in digital rain
* Fixing digital rain & typing heatmap if keyreactive effects are not enabled
* Apply suggestions from code review
Co-Authored-By: Drashna Jaelre <drashna@live.com>
* Adding parenthesizes to DRIVER_LED_TOTAL where necessary
* Updated docs
* added notes about parentheses
* RGB Matrix overhaul
Breakout of animations to separate files
Integration of optimized int based math lib
Overhaul of rgb_matrix.c and animations for performance
* Updating effect function api for future extensions
* Combined the keypresses || keyreleases define checks into a single define so I stop forgetting it where necessary
* Moving define RGB_MATRIX_KEYREACTIVE_ENABLED earlier in the include chain
* Remove unnecessary IS_COMMAND definition in clueboard/66/rev4
* Replace keyboard_report->mods with get_mods() in IS_COMMAND definitions
* Update docs to use get_mods() instead of keyboard_report->mods
* Replace keyboard_report->mods with get_mods() in tmk_core/protocol/usb_hid/test
For some reason, this occurrence used KB_LSHIFT and KB_RSHIFT, which don't exist
* Replace keyboard_report->mods with get_mods() in Massdrop keyboards (as per @patrickmt)
The debounce filtering reports a key/switch change directly, without any extra delay. After that the debounce logic will filter all further changes, until the key/switch reports the same state for the given count of scans.
So a perfect switch will get a short debounce period and a bad key will get a much longer debounce period. The result is an adaptive debouncing period for each switch.
This value defines how often the same key/switch state has to be detected in successive reads until the next key state can be reported.
In other words this value defines the minimum debouncing period for a switch.
* Remove chording as it is not documented, not used, and needs work.
* Make Leader Key an optional feature.
* Switch from `PREVENT_STUCK_MODIFIERS` to `STRICT_LAYER_RELEASE`
* Remove `#define PREVENT_STUCK_MODIFIERS` from keymaps.
With these changes, the ergodox ez goes from 315 scans per second
when no keys are pressed (~3.17ms/scan) to 447 (~2.24ms/scan).
The changes to the pin read are just condensing the logic, and
replacing a lot of conditional operations with a single bitwise
inversion.
The change to row scanning is more significant, and merits
explanation. In general, you can only scan one row of a keyboard
at a time, because if you scan two rows, you no longer know
which row is pulling a given column down. But in the Ergodox
design, this isn't the case; the left hand is controlled by an
I2C-based GPIO expander, and the columns and rows are *completely
separate* electrically from the columns and rows on the right-hand
side.
So simply reading rows in parallel offers two significant
improvements. One is that we no longer need the 30us delay after
each right-hand row, because we're spending more than 30us
communicating with the left hand over i2c. Another is that we're
no longer wastefully sending i2c messages to the left hand
to unselect rows when no rows had actually been selected in the
first place. These delays were, between them, coming out to
nearly 30% of the time spent in each scan.
Signed-off-by: seebs <seebs@seebs.net>
* include variables and .h files as pp directives
* start layout compilation
* split ergodoxes up
* don't compile all layouts for everything
* might seg fault
* reset layouts variable
* actually reset layouts
* include rules.mk instead
* remove includes from rules.mk
* update variable setting
* load visualizer from path
* adds some more examples
* adds more layouts
* more boards added
* more boards added
* adds documentation for layouts
* use lowercase names for LAYOUT_
* add layout.json files for each layout
* add community folder, default keymaps for layouts
* touch-up default layouts
* touch-up layouts, some keyboard rules.mk
* update documentation for layouts
* fix up serial/i2c switches
