b272c035ba
* fix CLI section links in the Summary * fix heading in Pointing Device doc * fix headings in PS/2 Mouse Support doc * add explicit section ids to I2C Master Driver doc * reformat GPIO Controls table Much like the I2C Master Driver doc, I found this a bit less than ideal to read. (The table was actually wider than the space available for it.) Reformatted so each GPIO function is an H3 heading, followed by a paragraph and a table of each architecture's old-style function. * migrate changes from I2C Master Driver doc to Japanese translation * add explicit anchors to I2C Master Driver docs * fix code block language markers The language markers are case-sensitive; using the wrong case means the syntax highlighting doesn't work. Good: ```c Bad: ```C * restore Japanese I2C Master Driver doc to current master Can't update the internal tracking references accurately until the changes to the English doc are committed to master. * add explicit anchors to edited files * change ChibiOS/ARM to ARM/ChibiOS Because ARM/ATSAM is also a thing that exists. * fix code block language markers again Used the wrong markers in a few spots. Also these are apparently always supposed to be lowercase. * add section anchors to cli.md * restore table formatting on GPIO Control doc * remove changes to _summary.md
7.4 KiB
PS/2 Mouse Support :id=ps2-mouse-support
Its possible to hook up a PS/2 mouse (for example touchpads or trackpoints) to your keyboard as a composite device.
To hook up a Trackpoint, you need to obtain a Trackpoint module (i.e. harvest from a Thinkpad keyboard), identify the function of each pin of the module, and make the necessary circuitry between controller and Trackpoint module. For more information, please refer to Trackpoint Hardware page on Deskthority Wiki.
There are three available modes for hooking up PS/2 devices: USART (best), interrupts (better) or busywait (not recommended).
The Circuitry between Trackpoint and Controller :id=the-circuitry-between-trackpoint-and-controller
To get the things working, a 4.7K drag is needed between the two lines DATA and CLK and the line 5+.
DATA ----------+--------- PIN
|
4.7K
|
MODULE 5+ --------+--+--------- PWR CONTROLLER
|
4.7K
|
CLK ------+------------ PIN
Busywait Version :id=busywait-version
Note: This is not recommended, you may encounter jerky movement or unsent inputs. Please use interrupt or USART version if possible.
In rules.mk:
PS2_MOUSE_ENABLE = yes
PS2_USE_BUSYWAIT = yes
In your keyboard config.h:
#ifdef PS2_USE_BUSYWAIT
# define PS2_CLOCK_PORT PORTD
# define PS2_CLOCK_PIN PIND
# define PS2_CLOCK_DDR DDRD
# define PS2_CLOCK_BIT 1
# define PS2_DATA_PORT PORTD
# define PS2_DATA_PIN PIND
# define PS2_DATA_DDR DDRD
# define PS2_DATA_BIT 2
#endif
Interrupt Version :id=interrupt-version
The following example uses D2 for clock and D5 for data. You can use any INT or PCINT pin for clock, and any pin for data.
In rules.mk:
PS2_MOUSE_ENABLE = yes
PS2_USE_INT = yes
In your keyboard config.h:
#ifdef PS2_USE_INT
#define PS2_CLOCK_PORT PORTD
#define PS2_CLOCK_PIN PIND
#define PS2_CLOCK_DDR DDRD
#define PS2_CLOCK_BIT 2
#define PS2_DATA_PORT PORTD
#define PS2_DATA_PIN PIND
#define PS2_DATA_DDR DDRD
#define PS2_DATA_BIT 5
#define PS2_INT_INIT() do { \
EICRA |= ((1<<ISC21) | \
(0<<ISC20)); \
} while (0)
#define PS2_INT_ON() do { \
EIMSK |= (1<<INT2); \
} while (0)
#define PS2_INT_OFF() do { \
EIMSK &= ~(1<<INT2); \
} while (0)
#define PS2_INT_VECT INT2_vect
#endif
USART Version :id=usart-version
To use USART on the ATMega32u4, you have to use PD5 for clock and PD2 for data. If one of those are unavailable, you need to use interrupt version.
In rules.mk:
PS2_MOUSE_ENABLE = yes
PS2_USE_USART = yes
In your keyboard config.h:
#ifdef PS2_USE_USART
#define PS2_CLOCK_PORT PORTD
#define PS2_CLOCK_PIN PIND
#define PS2_CLOCK_DDR DDRD
#define PS2_CLOCK_BIT 5
#define PS2_DATA_PORT PORTD
#define PS2_DATA_PIN PIND
#define PS2_DATA_DDR DDRD
#define PS2_DATA_BIT 2
/* synchronous, odd parity, 1-bit stop, 8-bit data, sample at falling edge */
/* set DDR of CLOCK as input to be slave */
#define PS2_USART_INIT() do { \
PS2_CLOCK_DDR &= ~(1<<PS2_CLOCK_BIT); \
PS2_DATA_DDR &= ~(1<<PS2_DATA_BIT); \
UCSR1C = ((1 << UMSEL10) | \
(3 << UPM10) | \
(0 << USBS1) | \
(3 << UCSZ10) | \
(0 << UCPOL1)); \
UCSR1A = 0; \
UBRR1H = 0; \
UBRR1L = 0; \
} while (0)
#define PS2_USART_RX_INT_ON() do { \
UCSR1B = ((1 << RXCIE1) | \
(1 << RXEN1)); \
} while (0)
#define PS2_USART_RX_POLL_ON() do { \
UCSR1B = (1 << RXEN1); \
} while (0)
#define PS2_USART_OFF() do { \
UCSR1C = 0; \
UCSR1B &= ~((1 << RXEN1) | \
(1 << TXEN1)); \
} while (0)
#define PS2_USART_RX_READY (UCSR1A & (1<<RXC1))
#define PS2_USART_RX_DATA UDR1
#define PS2_USART_ERROR (UCSR1A & ((1<<FE1) | (1<<DOR1) | (1<<UPE1)))
#define PS2_USART_RX_VECT USART1_RX_vect
#endif
Additional Settings :id=additional-settings
PS/2 Mouse Features :id=ps2-mouse-features
These enable settings supported by the PS/2 mouse protocol.
/* Use remote mode instead of the default stream mode (see link) */
#define PS2_MOUSE_USE_REMOTE_MODE
/* Enable the scrollwheel or scroll gesture on your mouse or touchpad */
#define PS2_MOUSE_ENABLE_SCROLLING
/* Some mice will need a scroll mask to be configured. The default is 0xFF. */
#define PS2_MOUSE_SCROLL_MASK 0x0F
/* Applies a transformation to the movement before sending to the host (see link) */
#define PS2_MOUSE_USE_2_1_SCALING
/* The time to wait after initializing the ps2 host */
#define PS2_MOUSE_INIT_DELAY 1000 /* Default */
You can also call the following functions from ps2_mouse.h
void ps2_mouse_disable_data_reporting(void);
void ps2_mouse_enable_data_reporting(void);
void ps2_mouse_set_remote_mode(void);
void ps2_mouse_set_stream_mode(void);
void ps2_mouse_set_scaling_2_1(void);
void ps2_mouse_set_scaling_1_1(void);
void ps2_mouse_set_resolution(ps2_mouse_resolution_t resolution);
void ps2_mouse_set_sample_rate(ps2_mouse_sample_rate_t sample_rate);
Fine Control :id=fine-control
Use the following defines to change the sensitivity and speed of the mouse.
Note: you can also use ps2_mouse_set_resolution for the same effect (not supported on most touchpads).
#define PS2_MOUSE_X_MULTIPLIER 3
#define PS2_MOUSE_Y_MULTIPLIER 3
#define PS2_MOUSE_V_MULTIPLIER 1
Scroll Button :id=scroll-button
If you're using a trackpoint, you will likely want to be able to use it for scrolling. It's possible to enable a "scroll button/s" that when pressed will cause the mouse to scroll instead of moving. To enable the feature, you must set a scroll button mask as follows:
#define PS2_MOUSE_SCROLL_BTN_MASK (1<<PS2_MOUSE_BUTTON_MIDDLE) /* Default */
To disable the scroll button feature:
#define PS2_MOUSE_SCROLL_BTN_MASK 0
The available buttons are:
#define PS2_MOUSE_BTN_LEFT 0
#define PS2_MOUSE_BTN_RIGHT 1
#define PS2_MOUSE_BTN_MIDDLE 2
You can also combine buttons in the mask by |ing them together.
Once you've configured your scroll button mask, you must configure the scroll button send interval. This is the interval before which if the scroll buttons were released they would be sent to the host. After this interval, they will cause the mouse to scroll and will not be sent.
#define PS2_MOUSE_SCROLL_BTN_SEND 300 /* Default */
To disable sending the scroll buttons:
#define PS2_MOUSE_SCROLL_BTN_SEND 0
Fine control over the scrolling is supported with the following defines:
#define PS2_MOUSE_SCROLL_DIVISOR_H 2
#define PS2_MOUSE_SCROLL_DIVISOR_V 2
Invert Mouse and Scroll Axes :id=invert-mouse-and-scroll-axes
To invert the X and Y axes you can put:
#define PS2_MOUSE_INVERT_X
#define PS2_MOUSE_INVERT_Y
into config.h.
To reverse the scroll axes you can put:
#define PS2_MOUSE_INVERT_H
#define PS2_MOUSE_INVERT_V
into config.h.
Debug Settings :id=debug-settings
To debug the mouse, add debug_mouse = true or enable via bootmagic.
/* To debug the mouse reports */
#define PS2_MOUSE_DEBUG_HID
#define PS2_MOUSE_DEBUG_RAW