forked from forks/qmk_firmware
301 lines
11 KiB
Markdown
301 lines
11 KiB
Markdown
# IS31FL3729 Driver {#is31fl3729-driver}
|
|
|
|
I²C 16x8/15x9 LED matrix driver by Lumissil. Supports a maximum of four drivers, each controlling up to 135 single-color LEDs, or 45 RGB LEDs.
|
|
|
|
[IS31FL3729 Datasheet](https://www.lumissil.com/assets/pdf/core/IS31FL3729_DS.pdf)
|
|
|
|
## Usage {#usage}
|
|
|
|
The IS31FL3729 driver code is automatically included if you are using the [LED Matrix](../features/led_matrix) or [RGB Matrix](../features/rgb_matrix) feature with the `is31fl3729` driver set, and you would use those APIs instead.
|
|
|
|
However, if you need to use the driver standalone, add this to your `rules.mk`:
|
|
|
|
```make
|
|
COMMON_VPATH += $(DRIVER_PATH)/led/issi
|
|
SRC += is31fl3729-mono.c # For single-color
|
|
SRC += is31fl3729.c # For RGB
|
|
I2C_DRIVER_REQUIRED = yes
|
|
```
|
|
|
|
## Basic Configuration {#basic-configuration}
|
|
|
|
Add the following to your `config.h`:
|
|
|
|
|Define |Default |Description |
|
|
|----------------------------|--------------------------------------|----------------------------------------------------|
|
|
|`IS31FL3729_SDB_PIN` |*Not defined* |The GPIO pin connected to the drivers' shutdown pins|
|
|
|`IS31FL3729_I2C_TIMEOUT` |`100` |The I²C timeout in milliseconds |
|
|
|`IS31FL3729_I2C_PERSISTENCE`|`0` |The number of times to retry I²C transmissions |
|
|
|`IS31FL3729_I2C_ADDRESS_1` |*Not defined* |The I²C address of driver 0 |
|
|
|`IS31FL3729_I2C_ADDRESS_2` |*Not defined* |The I²C address of driver 1 |
|
|
|`IS31FL3729_I2C_ADDRESS_3` |*Not defined* |The I²C address of driver 2 |
|
|
|`IS31FL3729_I2C_ADDRESS_4` |*Not defined* |The I²C address of driver 3 |
|
|
|`IS31FL3729_PWM_FREQUENCY` |`IS31FL3729_PWM_FREQUENCY_32K_HZ` |The PWM frequency of the LEDs |
|
|
|`IS31FL3729_SW_PULLDOWN` |`IS31FL3729_SW_PULLDOWN_2K_OHM_SW_OFF`|The `SWx` pullup resistor value |
|
|
|`IS31FL3729_CS_PULLUP` |`IS31FL3729_CS_PULLUP_2K_OHM_CS_OFF` |The `CSx` pulldown resistor value |
|
|
|`IS31FL3729_GLOBAL_CURRENT` |`0x40` |The global current control value |
|
|
|
|
### I²C Addressing {#i2c-addressing}
|
|
|
|
The IS31FL3729 has four possible 7-bit I²C addresses, depending on how the `AD` pin is connected.
|
|
|
|
To configure this, set the `IS31FL3729_I2C_ADDRESS_n` defines to one of the following in your `config.h`, where *n* denotes the driver index:
|
|
|
|
|Define |Value |
|
|
|----------------------------|------|
|
|
|`IS31FL3729_I2C_ADDRESS_GND`|`0x34`|
|
|
|`IS31FL3729_I2C_ADDRESS_SCL`|`0x35`|
|
|
|`IS31FL3729_I2C_ADDRESS_SDA`|`0x36`|
|
|
|`IS31FL3729_I2C_ADDRESS_VCC`|`0x37`|
|
|
|
|
### PWM Frequency {#pwm-frequency}
|
|
|
|
The PWM frequency can be adjusted by adding the following to your `config.h`:
|
|
|
|
```c
|
|
#define IS31FL3729_PWM_FREQUENCY IS31FL3729_PWM_FREQUENCY_32K_HZ
|
|
```
|
|
|
|
Valid values are:
|
|
|
|
|Define |Frequency |
|
|
|----------------------------------|----------------|
|
|
|`IS31FL3729_PWM_FREQUENCY_55K_HZ` |55 kHz |
|
|
|`IS31FL3729_PWM_FREQUENCY_32K_HZ` |32 kHz (default)|
|
|
|`IS31FL3729_PWM_FREQUENCY_4K_HZ` |4 kHz |
|
|
|`IS31FL3729_PWM_FREQUENCY_2K_HZ` |2 kHz |
|
|
|`IS31FL3729_PWM_FREQUENCY_1K_HZ` |1 kHz |
|
|
|`IS31FL3729_PWM_FREQUENCY_500_HZ` |500 Hz |
|
|
|`IS31FL3729_PWM_FREQUENCY_250_HZ` |250 Hz |
|
|
|`IS31FL3729_PWM_FREQUENCY_80K_HZ` |80 kHz |
|
|
|
|
### De-Ghosting {#de-ghosting}
|
|
|
|
These settings control the pulldown and pullup resistor values on the `SWy` and `CSx` pins respectively, for the purposes of eliminating ghosting. Refer to the datasheet (p. 18) for more information on how and why this occurs.
|
|
|
|
To adjust the resistor values, add the following to your `config.h`:
|
|
|
|
```c
|
|
#define IS31FL3729_SW_PULLDOWN IS31FL3729_SW_PULLDOWN_2K_OHM_SW_OFF
|
|
#define IS31FL3729_CS_PULLUP IS31FL3729_CS_PULLUP_2K_OHM_CS_OFF
|
|
```
|
|
|
|
Valid values for `IS31FL3729_SW_PULLDOWN` are:
|
|
|
|
|Define |Resistance |
|
|
|---------------------------------------|------------------------------|
|
|
|`IS31FL3729_SW_PULLDOWN_0_OHM` |None |
|
|
|`IS31FL3729_SW_PULLDOWN_0K5_OHM_SW_OFF`|0.5 kΩ in SWy off time |
|
|
|`IS31FL3729_SW_PULLDOWN_1K_OHM_SW_OFF` |1 kΩ in SWy off time |
|
|
|`IS31FL3729_SW_PULLDOWN_2K_OHM_SW_OFF` |2 kΩ in SWy off time (default)|
|
|
|`IS31FL3729_SW_PULLDOWN_1K_OHM` |1 kΩ |
|
|
|`IS31FL3729_SW_PULLDOWN_2K_OHM` |2 kΩ |
|
|
|`IS31FL3729_SW_PULLDOWN_4K_OHM` |4 kΩ |
|
|
|`IS31FL3729_SW_PULLDOWN_8K_OHM` |8 kΩ |
|
|
|
|
Valid values for `IS31FL3729_CS_PULLUP` are:
|
|
|
|
|Define |Resistance |
|
|
|-------------------------------------|------------------------------|
|
|
|`IS31FL3729_CS_PULLUP_0_OHM` |None |
|
|
|`IS31FL3729_CS_PULLUP_0K5_OHM_CS_OFF`|0.5 kΩ in CSx off time |
|
|
|`IS31FL3729_CS_PULLUP_1K_OHM_CS_OFF` |1 kΩ in CSx off time |
|
|
|`IS31FL3729_CS_PULLUP_2K_OHM_CS_OFF` |2 kΩ in CSx off time (default)|
|
|
|`IS31FL3729_CS_PULLUP_1K_OHM` |1 kΩ |
|
|
|`IS31FL3729_CS_PULLUP_2K_OHM` |2 kΩ |
|
|
|`IS31FL3729_CS_PULLUP_4K_OHM` |4 kΩ |
|
|
|`IS31FL3729_CS_PULLUP_8K_OHM` |8 kΩ |
|
|
|
|
### Global Current Control {#global-current-control}
|
|
|
|
This setting controls the current sunk by the `CSx` pins, from 0 to 255. By default, the value is 64, but if you need to adjust it, add the following to your `config.h`:
|
|
|
|
```c
|
|
#define IS31FL3729_GLOBAL_CURRENT 0x40
|
|
```
|
|
|
|
## ARM/ChibiOS Configuration {#arm-configuration}
|
|
|
|
Depending on the ChibiOS board configuration, you may need to [enable and configure I²C](i2c#arm-configuration) at the keyboard level.
|
|
|
|
## LED Mapping {#led-mapping}
|
|
|
|
In order to use this driver, each output must be mapped to an LED index, by adding the following to your `<keyboardname>.c`:
|
|
|
|
```c
|
|
const is31fl3729_led_t PROGMEM g_is31fl3729_leds[IS31FL3729_LED_COUNT] = {
|
|
/* Driver
|
|
* | R G B */
|
|
{0, SW1_CS1, SW1_CS2, SW1_CS3},
|
|
// etc...
|
|
};
|
|
```
|
|
|
|
In this example, the red, green and blue channels for the first LED index on driver 0 all have their anodes connected to the `SW1` pin, and their cathodes on the `CS1`, `CS2` and `CS3` pins respectively.
|
|
|
|
For the single-color driver, the principle is the same, but there is only one channel:
|
|
|
|
```c
|
|
const is31fl3729_led_t PROGMEM g_is31fl3729_leds[IS31FL3729_LED_COUNT] = {
|
|
/* Driver
|
|
* | V */
|
|
{0, SW1_CS1},
|
|
// etc...
|
|
};
|
|
```
|
|
|
|
These values correspond to the register indices as shown in the datasheet on page 12, figure 9.
|
|
|
|
## API {#api}
|
|
|
|
### `struct is31fl3729_led_t` {#api-is31fl3729-led-t}
|
|
|
|
Contains the PWM register addresses for a single RGB LED.
|
|
|
|
#### Members {#api-is31fl3729-led-t-members}
|
|
|
|
- `uint8_t driver`
|
|
The driver index of the LED, from 0 to 3.
|
|
- `uint8_t r`
|
|
The output PWM register address for the LED's red channel (RGB driver only).
|
|
- `uint8_t g`
|
|
The output PWM register address for the LED's green channel (RGB driver only).
|
|
- `uint8_t b`
|
|
The output PWM register address for the LED's blue channel (RGB driver only).
|
|
- `uint8_t v`
|
|
The output PWM register address for the LED (single-color driver only).
|
|
|
|
---
|
|
|
|
### `void is31fl3729_init(uint8_t index)` {#api-is31fl3729-init}
|
|
|
|
Initialize the LED driver. This function should be called first.
|
|
|
|
#### Arguments {#api-is31fl3729-init-arguments}
|
|
|
|
- `uint8_t index`
|
|
The driver index.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_write_register(uint8_t index, uint8_t reg, uint8_t data)` {#api-is31fl3729-write-register}
|
|
|
|
Set the value of the given register.
|
|
|
|
#### Arguments {#api-is31fl3729-write-register-arguments}
|
|
|
|
- `uint8_t index`
|
|
The driver index.
|
|
- `uint8_t reg`
|
|
The register address.
|
|
- `uint8_t data`
|
|
The value to set.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_set_color(int index, uint8_t red, uint8_t green, uint8_t blue)` {#api-is31fl3729-set-color}
|
|
|
|
Set the color of a single LED (RGB driver only). This function does not immediately update the LEDs; call `is31fl3729_update_pwm_buffers()` after you are finished.
|
|
|
|
#### Arguments {#api-is31fl3729-set-color-arguments}
|
|
|
|
- `int index`
|
|
The LED index (ie. the index into the `g_is31fl3729_leds` array).
|
|
- `uint8_t red`
|
|
The red value to set.
|
|
- `uint8_t green`
|
|
The green value to set.
|
|
- `uint8_t blue`
|
|
The blue value to set.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_set_color_all(uint8_t red, uint8_t green, uint8_t blue)` {#api-is31fl3729-set-color-all}
|
|
|
|
Set the color of all LEDs (RGB driver only).
|
|
|
|
#### Arguments {#api-is31fl3729-set-color-all-arguments}
|
|
|
|
- `uint8_t red`
|
|
The red value to set.
|
|
- `uint8_t green`
|
|
The green value to set.
|
|
- `uint8_t blue`
|
|
The blue value to set.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_set_value(int index, uint8_t value)` {#api-is31fl3729-set-value}
|
|
|
|
Set the brightness of a single LED (single-color driver only). This function does not immediately update the LEDs; call `is31fl3729_update_pwm_buffers()` after you are finished.
|
|
|
|
#### Arguments {#api-is31fl3729-set-value-arguments}
|
|
|
|
- `int index`
|
|
The LED index (ie. the index into the `g_is31fl3729_leds` array).
|
|
- `uint8_t value`
|
|
The brightness value to set.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_set_value_all(uint8_t value)` {#api-is31fl3729-set-value-all}
|
|
|
|
Set the brightness of all LEDs (single-color driver only).
|
|
|
|
#### Arguments {#api-is31fl3729-set-value-all-arguments}
|
|
|
|
- `uint8_t value`
|
|
The brightness value to set.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_set_scaling_register(uint8_t index, uint8_t red, uint8_t green, uint8_t blue)` {#api-is31fl3729-set-scaling-register-rgb}
|
|
|
|
Configure the scaling registers for a single LED (RGB driver only). This function does not immediately update the LEDs; call `is31fl3729_update_scaling_registers()` after you are finished.
|
|
|
|
#### Arguments {#api-is31fl3729-set-scaling-register-rgb-arguments}
|
|
|
|
- `uint8_t index`
|
|
The LED index (ie. the index into the `g_is31fl3729_leds` array).
|
|
- `uint8_t red`
|
|
The scaling value for the red channel.
|
|
- `uint8_t green`
|
|
The scaling value for the green channel.
|
|
- `uint8_t blue`
|
|
The scaling value for the blue channel.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_set_scaling_register(uint8_t index, uint8_t value)` {#api-is31fl3729-set-scaling-register-mono}
|
|
|
|
Configure the scaling registers for a single LED (single-color driver only). This function does not immediately update the LEDs; call `is31fl3729_update_scaling_registers()` after you are finished.
|
|
|
|
#### Arguments {#api-is31fl3729-set-scaling-register-mono-arguments}
|
|
|
|
- `uint8_t index`
|
|
The LED index (ie. the index into the `g_is31fl3729_leds` array).
|
|
- `uint8_t value`
|
|
The scaling value for the LED.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_update_pwm_buffers(uint8_t index)` {#api-is31fl3729-update-pwm-buffers}
|
|
|
|
Flush the PWM values to the LED driver.
|
|
|
|
#### Arguments {#api-is31fl3729-update-pwm-buffers-arguments}
|
|
|
|
- `uint8_t index`
|
|
The driver index.
|
|
|
|
---
|
|
|
|
### `void is31fl3729_update_scaling_registers(uint8_t index)` {#api-is31fl3729-update-scaling-registers}
|
|
|
|
Flush the scaling register values to the LED driver.
|
|
|
|
#### Arguments {#api-is31fl3729-update-scaling-registers-arguments}
|
|
|
|
- `uint8_t index`
|
|
The driver index.
|